Explosion proof loader is a special vehicle in construction machinery. The operator shall receive the training and guidance of the manufacturer, have a full understanding of the structure and performance of the machine, and obtain certain operation and maintenance experience to operate the machine. Running in period is an important link to ensure the normal operation of loader, reduce failure rate and prolong its service life. However, at present, some users ignore the special technical requirements of the running in period of the new loader due to lack of common sense of the loader, tight construction period, or want to obtain benefits as soon as possible.

注意磨合期的工作負荷，磨合期內的工作負荷一半不要超過額定工作負荷的70％，并要安排適合的工作量，防止機器長時間連續作業所引起的過熱現場的發生，引發各部件異常磨損。

Pay attention to the working load during the running in period. Half of the working load during the running in period shall not exceed 70% of the rated working load, and appropriate workload shall be arranged to prevent overheating on site caused by long-term continuous operation of the machine and abnormal wear of various components.

注意經常觀察各儀表指示，出現異常應及時停車予以排除，在原因未找到、故障未排除前應停止作業。經常檢查潤滑油、液壓油、冷卻液、制動液以及燃油油（水）位和品質，并注意檢查整機的密封性。檢查中發現油水缺少過多，應分析原因。同時，應強化各潤滑點的潤滑，建議在磨合期內，每班都要對潤滑點加注潤滑脂（特殊要求除外）。

Pay attention to regularly observe the indication of each instrument. In case of any abnormality, stop the machine in time for troubleshooting. Stop the operation before the cause is found and the fault is eliminated. Regularly check the level and quality of lubricating oil, hydraulic oil, coolant, brake fluid and fuel oil (water), and pay attention to the tightness of the whole machine. If too much oil and water is found during the inspection, the cause shall be analyzed. At the same time, the lubrication of each lubrication point shall be strengthened. It is recommended that each shift should add grease to the lubrication points during the running in period (except for special requirements).

保持機器清潔，及時調整、緊固松動的零部件以防因松動而加劇零部件的磨損或?qū)е铝悴考G失。在磨合期內使用保養就會減少早期故障的發生，延長使用壽命，提高作業效率，使機器為您帶來更多收益。

Keep the machine clean and adjust and fasten loose parts in time to prevent the wear of parts or loss of parts due to looseness. During the running in period, the use and maintenance will reduce the occurrence of early faults, prolong the service life, improve the operation efficiency, and make the machine bring you more benefits.

磨合期結束，應對機器進行強制保養，做好檢查和調整工作，同時注意油液的更換，建議更換廠家各種專用油液。

At the end of the running in period, the machine shall be subject to compulsory maintenance, inspection and adjustment. At the same time, pay attention to the replacement of oil. It is recommended to replace various special oils of the manufacturer.