Key points for attention after starting and during operation of loader

（1）裝載機發動機啟動后，等制動氣壓達到合適氣壓時再準備起步，以保障行車時的制動平穩性。有緊急制動的把緊急及停車制動閥的按鈕按下（只有當氣壓達到允許起步氣壓時，按鈕才能按下，否則按下去會自動跳起來），使緊急及停車制動釋放下，才能掛I擋起步。無緊急制動的只要將停車制動手柄放下，釋入停車制動就可以起步。

(1) After the loader engine is started, wait until the brake air pressure reaches the appropriate air pressure, and then prepare to start, so as to ensure the braking stability during driving. If there is emergency braking, press the button of the emergency and parking brake valve (the button can be pressed only when the air pressure reaches the allowable starting air pressure, otherwise it will jump up automatically) to release the emergency and parking brake, and then start in gear I. If there is no emergency braking, you can start as long as you put down the parking brake handle and release the parking brake.

（2）清理在行走道路上的故障物，要注意鐵塊、溝渠之類的障礙物，以免割破輪胎。

(2) Clean up the faulty objects on the walking road. Pay attention to obstacles such as iron blocks and ditches to avoid cutting the tire.

（3）將后視鏡調整好，使駕駛員入座后能有好的視野效果。

(3) Adjust the rearview mirror so that the driver can have a good field of vision when seated.

（4）保障裝載機的喇叭、后退信號燈，以及保險裝置能正常工作。

(4) Ensure that the horn, reverse signal light and safety device of the loader can work normally.

（5）在即將起步或在檢查轉向左右靈活到位時，應先按喇叭，以警示周?chē)藛T注意。

(5) When you are about to start or check that the steering is flexible and in place, you should first sound the horn to warn the surrounding personnel.

（6）在起步行走前，應對操縱手柄、踏板、方向盤先試一次，確定已處于正常狀態才能開始進入作業。要注意檢查轉向、制動是否完好。確定轉向、制動完全正常，方可起步運行。

(6) Before starting and walking, try the joystick, pedal and steering wheel first to confirm that they are in normal state before entering the operation. Pay attention to check whether the steering and braking are intact. Make sure that the steering and braking are completely normal before starting.

（7）行進時，將鏟斗置于離地400mm左右高度。在山區坡道作業或跨越溝渠等障礙時，應減速、小轉角，要注意避免傾翻。當裝載面在陡坡上開始滑向一邊時，須卸載，避免繼續滑下。

(7) When traveling, place the bucket at a height of about 400mm above the ground. When working on slopes in mountainous areas or crossing ditches and other obstacles, slow down and turn small corners, and pay attention to avoid tipping. When the loading surface starts to slide to one side on a steep slope, it must be unloaded to avoid further sliding.

（8）作業時盡量避免輪胎過多、過分打滑；盡量避免兩輪懸空，不允許只有兩輪著地而繼續作業。

(8) Try to avoid too many tires and excessive skidding during operation; Try to avoid two wheels hanging in the air, and it is not allowed to continue the operation with only two wheels landing on the ground.

（9）作牽引車時，只允許與牽引裝置掛接，被牽引物與裝載機之間不允許站人，且要保持相應的距離，避免出現事故。

(9) When the tractor is used, it is only allowed to be connected with the traction device. No one is allowed to stand between the towed object and the loader, and the corresponding distance shall be maintained to avoid accidents.

本文的精彩內容由礦用裝載機提供知識提供，本網站還有很多的精彩內容，更多的內容您可以點擊進入：http://yygsbaby.com我們有專門的客服為您解答問

The wonderful content of this article is provided by the mining loader. There are many wonderful contents on this website. You can click to enter more contents: http://yygsbaby.com We have special customer service to answer your questions