The loader factory teaches you how to change the tire quickly

因為小鏟車裝載機常常行走于在比較惡劣的工地(例如巖層面)工作，夏季天氣炎熱，輪胎氣壓不均衡加上地面的難題，可能會致使發生爆胎狀況，小型裝叉車和大家聊聊如何更換輪胎。

Because small forklift loaders often walk on poor construction sites (such as rock layers), hot summer weather, uneven tire pressure and ground problems may lead to tire blowout. Small forklift loaders talk about how to replace tires.

(1)啟動小型叉車設備，然后找到一個平坦開放的地方，按下動臂升降桿，使用動臂支撐將前輪胎與地面保持一定距離，然后在閃光橋附近的爆胎側使用支撐，并將后輪胎楔入。

(1) First start the small forklift equipment, then find a flat and open place, press the boom lifting rod, use the boom support to keep the front tire at a certain distance from the ground, then use the support at the tire burst side near the flash bridge, and wedge the rear tire.

(2)利用撬杠等工具，拆裝擋圈及鎖圈隨后查驗輪胎襯墊與輪圈外表面是否黏連。如果發生這種情況，可以拆除支架，使設備在短距離內緩慢來回運行，直到襯墊與輪輞外表面脫落；禁止轉彎和快速駕駛，以防止損壞內胎。隨后，前胎再次支撐起來。

(2) Use crowbar and other tools to disassemble and assemble the retaining ring and lock ring, and then check whether the tire liner is adhered to the outer surface of the rim. If this happens, the support can be removed to make the equipment run back and forth slowly in a short distance until the pad and the outer surface of the rim fall off; It is prohibited to turn and drive fast to prevent damage to the inner tube. Then, the front tire is supported again.

(3)將內、外胎的相對位置做好標識，便于搜索、異物和修復電動裝載機輪胎。

(3) The relative positions of the inner and outer tires shall be marked to facilitate the search, removal of foreign matters and repair of electric loader tires.

(4)用撬杠等工具從輪輞上拆下小叉車輪胎。注意，動作要柔和配合，默契，避免被輪胎撞，保護氣門口。

(4) Remove the small forklift tire from the rim with a crowbar and other tools. Note that the action should be soft and cooperative to avoid being hit by tires and protect the air door.

(5)外胎被鋼釘?shù)燃?xì)長異物刺傷后，如果表面無明顯傷口或傷口小，可繼續使用外胎（因為小叉車輪胎為低壓輪胎，運行速度慢）；如果傷口較大，必須進行修復(因為設備運行時，輪胎會被擠壓和摩擦，時間長了會損壞內胎，甚傷口越來越大，內胎突出，導致輪胎損壞。

(5) If there is no obvious wound or small wound on the surface after the outer tire is punctured by long and thin foreign bodies such as steel nails, continue to use the outer tire (because the small forklift tire is a low pressure tire and runs slowly); If the wound is large, it must be repaired (because the tire will be squeezed and rubbed when the equipment is running, and the inner tube will be damaged after a long time, or even the wound will become larger and larger, and the inner tube will protrude, leading to tire damage.

(6)如果是新內胎，必須擰緊閥口底部的螺栓，防止漏氣；然后外胎內壁的異物，撒上適量的輕鈣粉，擦拭均勻。為使襯墊與內、外胎緊貼，在裝入內胎后應給內胎適度打氣，再插入襯墊。

(6) If it is a new inner tube, the bolts at the bottom of the valve port must be tightened to prevent air leakage; Then remove the foreign matters on the inner wall of the outer tube, sprinkle an appropriate amount of light calcium powder, and wipe it evenly. In order to make the liner close to the inner and outer tubes, the inner tube shall be properly inflated after being installed, and then the liner shall be inserted.

(7)將輪胎放到輪圈上，安上鎖圈、擋圈；安裝過程中要保護好氣門嘴。

(7) Put the tire on the rim and install the lock ring and retaining ring; Protect the air valve nozzle during installation.

(8)用車載空壓機給輪胎打氣。

(8) Use the on-board air compressor to inflate the tire.

(9)按下動臂升降桿，取出支架；到目前為止，更換六噸裝載機輪胎需要大約50次min。

(9) Press the boom lifting lever and take out the bracket; Up to now, it takes about 50 times per minute to replace six ton loader tires.

以上就是為大家介紹的有關礦用裝載機的詳細的介紹,希望對您有所幫助.如果您有什么疑問的話,歡迎聯系我們.我們將以的態度,為您提供服務http://yygsbaby.com

The above is a detailed introduction to the mining loader, and we hope it will be helpful to you. If you have any questions, please contact us. We will provide you with professional services http://yygsbaby.com